SUR-SIZE™ Cut-To-Length Assembly SM-4/SM-6

More Views

SUR-SIZE™ Cut-To-Length Assembly SM-4/SM-6 | SM4/SM6

Related Models

Custom Cut-To-Length Units

The Building Blocks Of Automation

Build your own unit!
You may be able to apply for any of these additional products below.

  • Description
  • Testimonial
  • Options
  • Benefits
  • Specifications
  • Materials

The combination of a knife assembly and a roll feeder creates a Sur-Size™ cut-to-length assembly. The Sur-Size™ cut-to-length assemblies are capable of handling a wide variety of flexible materials. The cut to length assembly is a reliable, simple to use, self-contained module. It is a complete unit that delivers a finished product to your specifications. The unit can run to a length or to a registration mark.

Simple and easy to use, just enter the length and quantity on the color touch screen. The units automatically feed, measure, cut and count the pieces to a required size. After the exact number of pieces are cut, the unit stops. An end of cycle signal is provided once the cut is completed. For a single automated one shot process, this unit will feed and cut the material on demand. Clean cuts are provided by the guillotine knife assembly. Small guillotine cut-to-length assemblies are available in two configurations.

The integrated benchtop style unit is a convenient package for many users who just want to plug in a power cord, air line, and start cutting their product. It is available in two cut width sizes – 110mm (4in) or 160mm (6in). See FG models for information on modular style units.

We can support each of these Sur-size units around the world with our remote access. Each unit is built with a USB port which is directly connected to the controls. The unit can be connected to an internet interface utilizing a USB cable allowing tech support anywhere in the world. Support for resetting the unit, getting remote training, and even complete software upgrades are available. 

Just wanted to let you all know that we are EXTREMELY satisfied with the performance of the AZCO SM-6 cut-to-length machine purchased from you in 2002. From 1/03/08, we have just under 2 million machine cycles that have produced just over 4 million parts (one material only, the actual number is closer to 5 million parts). Over the complete time4 span of ownership, estimated machine cycles are approximately 10 million with 7,400,000 cycles since 10/19/05. Have produced WELL over 30 million parts with this one machine since date of purchase. Our FG-250V, while not used as much, has been exception also.
Keep up the good work.

D.P.
Electronics Company
California


We purchased an SM-4 unit back in 1994 and have only had to have the machine serviced once since then. We use the SM-6 everyday, producing about 1,000 cuts a day on average, cutting magnetic ribbon for planning boards. Definitely satisfied with our AZCO experience.

T.Z .
Communications Company
Missouri
  • No-product sensor
  • Product verification sensor
  • One-shot input and feedback output
  • Cut lengths to 55km/34 miles
  • Infeed roll unwind
  • Quantity count to 100 million
  • Outfeed conveyor
  • Steel drive roller
  • Easy to use as stand-alone unit
  • Easy operator interface with a color touch pad
  • Enter lengths in either inches or metric
  • Module knife cartridge
  • On demand one shot
  • Reduced scrap
  • Eliminates the need for a large inventory of cut product
  • Minimum Length: 0.1mm/0.005"
  • Maximum Quantity Count: 999,999
  • Power requirements: 110 V AC or 220 V AC
  • 30 - 90 psi (2 - 6 bar) compressed air
  • Accuracy: +/-0.38mm/0.015" or 0.1% of cut length (whichever is larger)

Absorbent pads, film, felt, foam, foil, gaskets, hose, laminates, mesh, metalized film, nonwoven, pads, paper, personal care products, PTFE, rubber, shrink tubing, tape, test strips, thin gauge metal, tubing, Velcro

WARNING! UNIT MUST BE PROPERLY GUARDED AT ALL TIMES TO MEET ALL STATE, FEDERAL, AND LOCAL REQUIREMENTS

Get More Information

Captcha

* Required Fields